Back to Blog

Kitchen Hood Suppression Inspections: Every 6 Months, and What Fails in Between

By Ironclad Fire Protection · · 6 min read

A kitchen hood suppression system needs an inspection by a licensed company every six months. NFPA 96 and NFPA 17A both set that interval, and the clock runs from the date on your last tag.

In between, you are supposed to check it yourself once a month. That check takes about five minutes, and almost nobody does it.

This article covers what each check involves, who is responsible when you lease your space, and what goes wrong between visits.

What Is Due, and How Often

Four intervals apply to a hood system. Only the first one is yours.

IntervalWhat happensWho does it
Every monthA visual check of the systemYou or your staff
Every 6 monthsFull inspection, new tag, and a written reportA licensed company
Every 6 monthsMetal alloy fusible links replacedA licensed company
Every 12 yearsHydrostatic test of the tank and hosesA licensed company

If you lease a restaurant space, the inspection is almost always your job, not the landlord’s. A restaurant tenant usually carries this kind of maintenance. Check your lease if you are not sure, but plan on booking it yourself.

In Tennessee, the company doing the work needs more than an extinguisher license. The state can limit a license to portable extinguishers only under rule 0780-02-14-.09.

A hood system is a fixed system, and fixed systems take an endorsement on top of the license. When you call a company, ask whether their license covers fixed systems.

What Happens at the 6-Month Inspection

Plan on about two hours, scheduled before you open or after you close. The cooking line has to shut down for at least part of the visit.

I check the tank and its pressure, the fusible links, the nozzles and their caps, the manual pull station, and the shutoff that kills the gas or power to the line. Then the system gets a new tag and you get a written report.

Ironclad’s Field Experience

I replace the fusible links at every visit. NFPA 96 requires metal alloy links to be replaced at least every six months, so a link should never ride from one inspection to the next.

If a kitchen will not shut the line down, I note it on the report and do as much as I can. My job is to tell you what is supposed to happen, not to argue about it.

If the system needs a repair, I tell you what it is and what it costs before I do the work. Parts I have to order usually take two to three weeks.

What Fails Between Visits

A nozzle cap keeps grease out of the nozzle so the agent can get out when the system fires.

Ironclad’s Field Experience

The two things I find most often are bad fusible links and missing or greasy nozzle caps.

Less often, a tank has lost pressure or is due for its 12-year hydrostatic test. I usually order a replacement tank rather than sending yours out, because it is faster.

Sometimes the kitchen moved or swapped a fryer or a range, and the nozzles no longer point at the equipment they were built to cover.

Grease Is What Turns a Small Fix Into a Big One

When a hood is not cleaned often enough, the grease hardens on the detection line. The cable, the piping, and the link brackets end up bound together in one solid mass.

Ironclad’s Field Experience

At that point the whole detection line has to be redone, not just the links. Sometimes you can barely get the fusible links off.

Stretching your hood cleaning schedule saves money on cleaning and costs it back on the suppression system.

Hood Cleaning Is a Separate Job

Most owners already know this, but it is worth saying once. I inspect the suppression system and I do not clean hoods. Hood and duct cleaning is its own vendor on its own NFPA 96 schedule.

The two jobs touch the same equipment, and that causes one problem worth knowing about. A hood cleaner can accidentally set off the suppression system, and an emergency recharge can cost thousands of dollars.

Keep both vendors on your calendar, and know who you will call if the system discharges. A system that dumped needs a recharge and a new tag before you cook again, and that is a different appointment from an inspection.

Your Monthly Check

NFPA 17A asks the owner to look the system over every month, following the manufacturer’s owner manual. You do not need any tools. Walk the line and check these five things:

  1. The pull station is clear and easy to reach, with nothing hanging on it or stacked in front of it.
  2. The Class K extinguisher is mounted in its spot near the cooking line.
  3. Every nozzle has its cap on, and nothing is blocking the nozzles.
  4. The tank gauge reads in the green, if your system has one you can see.
  5. The tag is there and less than six months old.

Ironclad’s Field Experience

Almost nobody does this check. Once in a while I meet someone who does.

What I see instead is the pull station used as a coat hanger and the Class K extinguisher used as a door stop. Most people have no idea how the system works.

What the Fire Marshal Looks At

The marshal usually checks two things: the tag date and the submitted report. If your system was already written up, they want a new tag and a report showing what was fixed.

Several Middle Tennessee cities track suppression reports online. See which cities require them and who files the report.

The hood system does not replace your extinguishers. A Class K unit still belongs near the cooking line, and our Nashville suppression guide covers that and how to pick a company.

What an Inspection Costs

The price rises with the number of systems and the drive to reach you. Parts and repairs are quoted on site before any work is done.

Is your hood system due for its six-month inspection? Request a quote for kitchen hood suppression service in Middle Tennessee.

Is Your Hood System Due?

Request a quote for kitchen hood suppression system inspection and we'll call you as soon as we can during business hours. Serving Nashville and Middle Tennessee.

Request a Quote